Zigbee Range Extender - FRIZREXZB-111

Für eine deutsche Übersetzung Klicken Sie hier

For more information about the product follow the respective links:

• Online User Guide

Precautions

• WARNING: For safety reasons, always make sure to disconnect the Range Extender from the power socket before removing the front cover.
• Do not remove the product label as it contains important information.
• Be aware that electronics are sensitive to static electricity, so aim to discharge before touching, and avoid touching any components inside the device.
• Do not paint the device
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
• The socket-outlet shall be installed near the equipment and shall be easily accessible

Installation:

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

1. Open the casing of the device by removing the screw at the bottom of the device.
2. Use the included screws to mount the Zigbee Range Extender on the wall.
3. Attach the front cover to the device by hooking the front cover to the top of the mounted device and pushing the front cover against the device.
4. Insert a screw at the bottom of the device.
5. Insert the plug of the cable attached to the Range Extender into a power socket
6. When the device is powered up, the Zigbee Range Extender will start searching (up to 15 minutes) for a Zigbee network to join. While the Range Extender is searching for a Zigbee network to join, the yellow LED flashes.
7. Make sure that the Zigbee network is open for joining devices and will accept the Renage Extender.
8. When the LED stops flashing, the Range Extender has successfully joined the Zigbee network.
9. If the scanning has timed out, a short press on the menu button will restart it.

ALTERNATIVE INSTALLATION OPTION

Another installation option is to replace the included cable with an alternative cable. If the installation consists of an in-wall cable, drill a hole in the marked area, through which the cable needs to be inserted, and connect the cable to the Zigbee Range Extender.

Placement

• Indoors at a temperature between 0-50°C.
• On a wall, where it is reachable for maintenance.

Modes

• SEARCHING GATEWAY MODE:  The yellow LED flashes
• MAINS POWERED: The green LED is on
• BATTERY BACKUP (MAINS FAILURE): The green LED flashes. This means that there is a mains failure, e.g. due to a power outage, and the device runs on battery for up to 14 hours.

Resetting

Resetting is needed if you want to connect your Zigbee Range Extender to another gateway or if you need to perform a factory reset to avoid abnormal behaviour.

1. Connect the Zigbee Range Extender to a power outlet.
2. Press and hold the menu button of the device
3. While you are holding the button down, the yellow LED first flashes once, then two times in a row, and finally numerous times in a row.
4. Release the button while the LED is flashing numerous times in a row.
5. After you release the button, the LED shows one long flash, and the reset is completed

Fault finding and cleaning

• In case of a bad or wireless weak signal, change the location of the Zigbee Range Extender. Otherwise, you can relocate your gateway or strengthen the signal with a smart plug.
• If the search for a gateway has timed out, a short press on the button will restart it.

Specifications 

• Dimensions: (W x D x H) 119 x 49 x 23 mm
• Color: White
• IP class: IP20
• Power Supply: 230V +/- 10%
• Power consumption: 0,4 W
• Operation temperature: 0 to +45°C
• Wireless protocol: Zigbee 3.0 Mesh
• Router: Yes
• Plug Type: C (EU) & G (UK)