Für eine deutsche Übersetzung Klicken Sie hier
For more information about the product follow the respective links:
Precautions
- Do not remove the product label as it contains important information. • When mounting with tape, make sure the surfaces are clean and dry.
- When mounting with tape, the room temperature should ideally be between 21° C and 38° C and minimum 16° C.
- Avoid mounting with tape on rough, porous or fibered materials such as wood or cement, as they reduce the tape bond
- Do not ingest battery, Chemical Burn Hazard.
- This product contains a coin cell battery. If the cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
- Keep new and used batteries away from children.
- If the battery compartments do not close securely, stop using the product and keep it away from children.
- If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
- Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;
- A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
Join to Network
- Press the button to activate a search for network. The Smart Button will start searching (up to 15 minutes) for a Zigbee network to join.
- Make sure that the Zigbee network is open for joining devices and will accept the Smart Button.
- While the device is searching for a Zigbee network to join, the yellow LED flashes.
- When the LED stops flashing, the device has successfully joined the Zigbee network.
- If the scanning has timed out, a short press on the button will restart it.
Mounting
- If you want to mount the Smart Button on the wall, you can use the included tape.
- Put the double adhesive tape on the back of the device and press firmly on the device with the tape to make it stick to the wall.
Using
- To activate an action or flow, press the button once
- The Smart Button is water-proof and thus suited for indoor and outdoor use. For use as a doorbell mount the button outside the door with the double adhesive tape.
As alarm button
- If the button is configured as an alert button, you press the button to activate the alarm. The red LED will then start flashing, signaling that the alarm is activated.
- To disable the alarm, press the button for 3 seconds. When the alarm is disabled, the red LED will stop flashing
Reset
- Press and hold the button for 10 seconds. Release the button immediately when the LED flashes green. You now have 60 seconds to reset the device.
- Press the button again and hold it.
- While you are holding the button down, the LED flashes yellow once, then two times in a row, and finally numerous times in a row.
- Release the button while the LED is flashing numerous times in a row.
- After you release the button, the LED shows one long flash, and the reset is completed.
Fault finding and cleaning
- In case of a bad or weak wireless signal, change the location of the Smart Button. Otherwise, you can relocate your gateway or strengthen the signal with a smart plug.
- If the search for a gateway has timed out, a short press on the button will restart it.
Battery replacement
The device will flash twice every minute when the battery is low.
CAUTION: RISK OF EXPLOSION IF THE BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF THE BATTERY IN ACCORDANCE WITH INSTRUCTIONS.
CAUTION: When removing cover for battery change - Electrostatic Discharge (ESD) can harm electronic components inside.
- To replace the battery, remove the screws in the back of the device and open the casing (note that you need a T6 Torx screwdriver to install and remove these screws). Replace the battery (CR2450) respecting the polarities. Close the casing and install the screws in the back of the device.
Specifications
- Dimensions: (W x D x H) 40 x 53 x 10,8 mm
- Color: White
- IP class: IP44
- Battery: CR2450
- Battery life: 3 years
- Operation temperature: 0 to +50°C
- Relative humidity: 5% to 85% non-condensing
- Wireless protocol: Zigbee 3.0