Für eine deutsche Übersetzung Klicken Sie hier

For more information about the product, follow the respective links:


Precautions

  • Do not remove the product label as it contains important information.
  • Be aware that electronics are sensitive to static electricity, so aim to discharge before touching, and avoid touching any components inside the device.
  • Do not paint the device.
  • Do not use tape for mounting the device outdoors.
  • Do not use tape for mounting if you will use the device for security purposes, as the tamper switch will not function.
  • When mounting with tape, make sure the surfaces are clean and dry
  • When mounting with tape, the room temperature should ideally be between 21° C and 38° C and minimum 16° C.
  • Avoid mounting with tape on rough, porous or fibered materials such as wood or cement, as they reduce the tape bond.


CAUTION: 

  • Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
  • Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;
  • A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.


Join to Network

  1. Insert batteries into the device respecting the polarities.
  2. When the batteries are inserted, the Intelligent Keypad will start searching (up to 15 minutes) for a Zigbee network to join. While the Intelligent Keypad is searching for a Zigbee network to join, the yellow LED flashes.
  3. If the scanning has timed out, a short press on the menu button inside the device will restart it. 
  4. After connecting the device to a network, attach the device to the back plate by hooking the device to the top of the back plate and pushing the device against the back plate.
  5. Finally, reinsert the screw at the bottom of the device.


Placement

  • You can place the Intelligent Keypad both indoors and outdoors in 0-50°C. 
  • Place the device, so it is easily accessible to users. 
  • Avoid placing the device in direct sunlight. 
  • Avoid placing the device in places exposed to direct rain. 
  • Avoid placing moving items 40 cm or less from the Intelligent Keypad, as they will activate the presence sensor. 
  • When mounting the device outdoors, use screws rather than tape.


Installation

  1. Open the casing of the device by removing the screw at the bottom of the device. 
  2. Open the casing of the device by removing the screw at the bottom of the device.
  3. Alternatively, you can use the double adhesive tape to mount the backplate. Make sure to press firmly on the backplate with the tape to make it stick. 


Reset your device


Resetting is needed if you want to connect your Intelligent Keypad to another gateway or if you need to perform a factory reset to avoid abnormal behavior.

 

  1. Open the casing of the device by removing the screw at the bottom of the device.
  2. Press and hold the menu button inside the device with a thin pin – e.g. a paper clip
  3. While you are holding the button down, the LED first flashes once, then two times in a row, and finally numerous times in a row. 
  4. Release the button while the LED is flashing numerous times in a row. 
  5. After you release the button, the LED shows one long flash, and the reset is completed.

Battery replacement


CAUTION: RISK OF EXPLOSION IF BATTERIES ARE REPLACED BY AN INCORRECT TYPE. DISPOSE OF THE BATTERIES IN ACCORDANCE WITH INSTRUCTIONS 

CAUTION: When removing cover for battery change - Electrostatic Discharge (ESD) can harm electronic components inside 

  1. To replace the batteries, remove the screw at the bottom of the device and open the casing.
  2. Replace all four batteries inside the device, respecting the polarities. 
  3. Reattach the device to the backplate and reinsert the screw at the bottom of the device


 

Fault finding

  • In case of a bad or wireless weak signal, change the location of the device. Otherwise you can relocate your gateway or strengthen the signal with a smart plug. 
  • If the search for a gateway has timed out, a short press on the button will restart it. 


Specifications

  • Frequency: Zigbee 3.0
  • Dimensions: 90 x 90 x 22 mm
  • Color: White
  • Battery: 2x AA LR6 Alkaline
  • Battery Life: 12 Months
  • Operation temperature: 0 to +50°C
  • Relative humidity: 5% - 85%, non condensing
  • RFID: 
    • Supports tags following the standards: ISO14443A and MIFARE classic
    • All tags must have each their own unique identifier (UID)
    • Reading distance: ~5 cm.